Fluke Networks FI-7000 FiberInspector™ Pro - FI2-7000-MPO INT
Fast delivery from stock MOQ's apply on some items
Need some help? Call us on 01403 754233
- Automated Pass/Fail certification of fibre optic connector end-faces
- Graphical indication of problem areas due to contamination, pits, chips, and scratches
- Certify to industry standards - IEC 61300-3-35
- Eliminate human subjectivity from fibre optic connector end-face measurements
- Save fibre optic connector end-face views during certification process
- Versiv™ modular design supports copper certification, fibre optic loss, OTDR testing and fibre end-face inspection
- Perfect for fibre inspection
Fibre optic connector end-face contamination is a leading cause of fibre failures. Dirt and contaminant cause insertion loss and back-reflection that inhibits optical transmission and causes havoc with transceivers. Fibre loss and OTDR testing can expose this problem, but in many cases, dirty connections make fibre testing time consuming and inaccurate.
Since dirt can be an issue before, during, or after fibre optic certification testing, and migrate from one fibre optic connector end-face to another upon mating, both sides of any connection must always be cleaned and inspected. Further, mating contaminated fibre optic connectors can cause permanent damage as microscopic debris is crushed between end-faces in physical contact. Even factory terminated patch cords or pigtails must be inspected as protective caps do not keep fibre optic connector end-faces clean. Avoiding this common cause of failure, starts with inspecting the fibre optic connector end-face and eliminating any contamination before insertion into a bulkhead or piece of equipment.
The FI-7000 FiberInspector Pro is a fibre optic inspection scope that allows you to inspect and certify fibre optic connector end-faces in 1 seconds so you can get the job done the first time. This fibre optic inspection scope provides automated PASS/FAIL certification take the guess work out of fibre inspection so anyone can be a fibre expert.
Features
- Fiber Inspection Certification
- Graphical indication of Problem Areas
- Store End-face Images
- Built on the Versiv Platform
- Versiv’s ProjX™ System
- Taptive™ User Interface
- LinkWare™ Live Test Results Management Service
- LinkWare™ Management Software
- PASS/FAIL Fiber End-face Grading
| Inspection Probe specifications | |
| 2M pixels | Blue LED |
| Light source | Blue LED |
| Power source | Versiv mainframe |
| Field of View (FOV) | Horizontal: 425 µm |
| Vertical: 320 µm | |
| Minimum detectable particle size | 0.5 µm |
| Dimensions | Approximately 6.75 in x 1.5 in (1175 mm x 35 mm) without adapter tip |
| Weight | 200 g |
| Temperature range | Operating: 32°F to 122°F (0 °C to +50 °C) |
| Storage: -4°F to +158°F (-20°C to +70°C) | |
| Certifications | CE |
| General specifications | |
| Weight | Mainframe with module and battery: 3 lbs, 5 oz (1.28 kg) |
| Dimensions | Mainframe with module and battery: 2.625 in x 5.25 in x 11.0 in ( 6.67 cm x 13.33 cm x 27.94 cm) |
| Battery | Lithium ion battery pack, 7.2 volts |
| Battery life | Eleven hour with Inspection probe attached |
| Charge Time | |
| Tester Off | Four hours to charge from 10% to 90% capacity |
| Tester On | Six hours to charge from 10% to 90% capacity with the tester on |
| Environmental specifications | |
| Operating temperature* | -18ºC to 45ºC |
| Non-operating temperature | -30ºC to 60ºC |
| Operating altitude | 4,000 m (13123 ft) |
| 3200 m (10,500 ft) with ac adapter | |
| Storage altitude | 12,000 m |
| EMC | EN 61326-1 |
| * Do not keep battery at temperatures below -20°C (-4°F) or above 50°C (122°F) for periods longer than one week to maintain battery capacity. |
